5 Common Plumbing Problems At Home And Solutions That Can Be Done Alone

Published by muhammad zajuli on

marketingpreis-sport.com

The situation when the water pipe at home is free from problems is directly proportional to the chance you have a supply of clean water for daily needs. Which homeowner doesn’t crave this? But unfortunately, the reality is not always that sweet. Water pipes are often a problem that scratches the head (and body!) When it threatens the presence of clean water at home and makes it difficult for you to take a shower or even just wash your hands.

If it turns out we share the same concerns regarding this, you are on the right page! Next Beres.id team shares 5 common problems plumbing fittings at home, complete with several solutions that you can do yourself. Enjoy listening!

1. Clogged Pipe

Most annoying when the moment of realizing this problem occurs when trying to wash the dishes after a family meal session. Water will pool and cannot be channeled into the pipe because it is blocked. The initial step is to check if there is a pile of leftover rice or other types of food that are clogging in the filter strainer. But if this has been done and the water is still not working, do the following steps.

Solution:

  • Try using a plunger or plumbing cleaner. Before the cleaning process using this tool, you should first flush the pipe with enough hot water so that the surface to be cleaned is softer and the dirt that sticks to it is easier to lift.
  • Give the liquid mixture consisting of hot water, baking soda, and vinegar into the drain pipe.
  • Recognize the causes of clogging to avoid similar cases from happening again in the future. Among the many possibilities, the top few are oil, fat, and other food traces. Make it a habit to always discard food scraps on a plate, if any, before putting it in the dishwasher.

2. Leaking faucet

Klak, Klak, Klak, Klak, Klak … The most annoying noise to the ears of the homeowners who came from the leaky faucet in their kitchen or bathroom. Not just a matter of discomfort, a leaky faucet that has been classified as severe also affects the wasteful use of water at home.

Solution:

  • Try tinkering with the ring on the tap. Did not rule out the object is not in the right position because it was nudged during previous use.
  • Cover with a special plaster, the pipe is leaking at the source of the leak.
  • This is only temporary, after which you can consider replacing the tap with a new one or dismantling the whole section and looking for sources of leakage from the inside.
  • Make sure you have complete tools in handling this. If you are doubtful but remain determined to deal with improvised devices, the leak will get worse.
  • Leave this one to the experts.

3. Damage to the Toilet Flush Tool

There are two possible common damages (headsup: both are not fun!) Ie when the flush device cannot stop working or the flush tool does not work at all. The first problem occurs because there is a leak in the water channeling portal to clean toilets that should be controlled. So it is a disaster when water continually overflows, and a greater disaster when there is ‘dirt’ when it happens. The second problem occurs when there is a blockage in the pipeline which is usually a path for dirt to go to landfills.

Solution:

  • For flush toilets that cannot stop working, check the feasibility of the valve or valve that is the center of water flow control in the toilet.
  • It could be that the valve is too loose or a malfunction occurs due to its working power which has gotten worse because it has been used for too long. If it’s like this, replace it with a new one.
  • For flushes that don’t work / clogged toilets, do it properly as you handle clogged water pipes. Always assume stubborn dirt is sticking.
  • Use traditional methods such as using a plunger, rinsing it with a baking soda mixture, or bypassing it by calling the suction toilet service.

4. Low Water Pressure

This is no less annoying. Imagine you are in a hurry to go to work or school, but must be hindered because the shower can not provide you enough clean water for bathing. The cause of this may be the problem (leak) of the pipe, or damage that is indeed from the network or center.

Solution

  • Not often, the culprit is limited to the shower cap that needs to be adjusted.
  • If it’s like this, try cleaning the shower head by brushing it and freeing it from various stubborn dirt.
  • Check that the shower head is installed correctly. If loose, fast. If it is too tight, adjust it while trying to see if water will come out.
  • Replace the shower head with a new one. Do not rashly uninstall itself if there is no background or previous related experience.
  • Leave it to the experts to do the dismantling and installation.

5. Pipe Leaks

One of the main actors of the problem mentioned earlier. In addition, a leaky pipe also has the potential to pollute a house with a pool of water and will be dangerous for homeowners, especially those of you who have your baby.

Solution

  • Look for points (we hope only one! Well, it’s better not to have at all!) Leak by doing a thorough inspection. Mark and act.
  • Note: make sure you have closed the faucet and let the pipe dry naturally afterward before performing the following steps.
  • Sand enough to the part that leaked and then you put a waterproof adhesive tape on that part. This applies to leaks that are not yet serious.
  • If double protection is deemed necessary, first apply an adhesive liquid (epoxy) to the leak (make sure that the pipe is completely dry naturally after the faucet is turned off).
  • Cover the surface and wait for a few hours and then you tape the waterproof adhesive tape to the surface given the epoxy.
  • Cut the leaking part and replace it with a new piece of pipe.

Those are some solutions that you can make references at home when this annoying event occurs. But keep in mind, many professional and trusted experts are available out there and are ready to help you.