15 Ways to Overcome Water Problems at Home with Simple Plumbing Repair

Published by muhammad zajuli on

Plumbing Fittings

Water systems and pipes in the house have an important role for the home and family life. Daily activities such as cooking, bathing, washing and others are very dependent on the water system and pipes in the house. Therefore, the water system in the home must really be considered for its continuity so as not to have an impact on daily life. However, after being used for a period of time, various factors can cause problems in the water system in the house, such as leakage, blocked ducts or broken pipes. In the following article, there are 15 ways to overcome water problems in the home that can be useful and needed by anyone.

1. Handle clogged pipes

The main cause of blockage is usually food, which accumulates over a long period of time so that water cannot flow. You can check and clean your own pipeline by removing food scraps trapped in the Plumbing by using fat removal ingredients and food scraps available on the market.

2 Handle leaking faucets

Faucets in the bathroom, toilet or kitchen after several uses can easily leak. Due to oxidation in the faucet or valve in the open channel, the solution for the clogged faucet is to use a steel wire material coated with iron layers or with a small tin inserted into the hole of the faucet, then use a hammer to crush steel or tin into the slot evenly, flat with a water pipe. Then, use the iron on the body of the bicycle and cut it into pieces 0.3 – 0.6 cm long. Use wire to tie it tightly.

3. Deal with pipe leaks with the coupling technique

To deal with pipe leaks with a coupling technique, you first need to prepare glue, glue that is suitable for dealing with problems like this. When using adhesives or binders, easily apply glue around the connecting ring, and rotate it so that it binds with the coupling technique.

4. Check pipe leaks due to cracks

To overcome the pipe leakage due to cracks, first use black tape or adhesive to tighten and close the crack, and make sure you leave the remaining tape on each side of the crack about 1 cm each so that there will be no water leakage.

5. Water pipes that are clogged in the toilet

The best way to deal with clogged pipes in the toilet is to turn off the water flow immediately when problems with the pipes arise. Then, use solid metal or vacuum to catch and open the pathway that is clogged with garbage.

6. Toilets that release water due to clogged drains

To overcome this problem, you first need to clog the drain in the toilet and empty the water tank. Next, remove the damaged blockage to clean it with vinegar, soap and detergent. Then, put it back as usual, open the drain that is clogging the toilet.

7 The toilet that drains water to the bathroom floor

First of all, you need to close the drain valve into the tank, use a dry cloth to absorb water in the toilet. Then, move parts such as tank caps, toilet seat covers, water containers, and be careful not to contact the contact points. Then, clean or replace with a new one if needed.

8. A toilet that draws water from a water tank

If the toilet leaks from the tank, all you have to do is move the rubber part to do the cleaning. Then, attach and tighten it, and if you have difficulty removing it, you can replace this part with more affordable rubber that is in stores.

9. The toilet is leaking from the handle and water reservoir

The cause of this problem is that the regulation of the water flow that is installed is too high compared to regulations, causing the water source to the water reservoirs not to accommodate excess water. The treatment you can give is to check the water limit according to product standards offline.

10 Condensing clogged drainage pipes

When you experience this problem, first check the drain, whether there are cracked parts or not. In the case of a drain pipe, check the outside of the drain pipe from the heat outside, whether it is clogged or blocked by the drain. You can also test the tube, vacuum or blow it up to allow dust or water clots to escape from the blockage if any.

11. Leakage on old washing machines

Many causes of damage to the washing machine are due to the connection between the hose is installed loose and not in accordance with the water tap. You can tighten the connection by adding new rubber around the drain pipe connection.

12. There is a leak at the bottom of the washing machine

Possible causes are the supply of water to the washing machine that is damaged or leakage in the pipe.

13 Leaks after using the washing machine

The cause of this problem is usually a reduced water supply or damage during the washing machine is working. Or, if the washing machine is not installed properly, this can cause water to overflow.

14. The sink is clogged in the trigger for the release of water

In this case, the action to check whether the device triggers the discharge of water is related to a diversion, and to re-glue the support if available.

15. Washing place that is not dry to the maximum

If there is a problem, you should check the drain hose to see if something is trapped and clear out any trash or obstacles found.

Categories: Plumbing